Chain Complete Kit Steel Raptor Yfm 350 S 2004- Quad Yamaha

  
Delivery times may vary, see cgv contact us before buying for exact times. Clicking immediate purchase, the customer acknowledge and agree to the terms and conditions!

Available at the bottom of this page! With standard reinforced chain, sprockets and quick coupler. Concentrate of performance and reliability, our chains kits provide excellent transmission of engine power to the rear wheel through a limitation of friction.

Black chain link - quick coupler. Brand: rk / tsubaki / SIFAM (Made in Japan). This article fits the vehicles. Picture not contractual, illustrative example !! Enhanced Standard (oro, eb) 250 cm3 Max super reinforced (rh) 500 cm3 Max hyper reinforced (rs rs3 rx) 500 cm3 and more.

Super oring: Standard O-rings (orn) normal / intensive road. Hyper oring: advanced O-rings (gold).

Special oring: competition O-rings (orh). how to see if it is time to change?

With wear and tear, the chain sallonge and relaxes. To tighten, pulling the wheel towards the rear through the turnbuckles located against the nuts on the wheel axle. Close to the tension, there is tension pins.

They are used to adjust the left and right tensioners symmetrically and see when approaching the limit race. If retendant in your channel, you reach the end of these markers is that it is time to change it. So in general, changing your channel kit. The teeth of the pinion and of the crown.

You can also observe the teeth of the pinion and the crown. If they are rounded or flashes, or downright crooked ... It is downright time to change. You can also test your system by grasping it between two fingers at the crown, and pulling backwards. If you can find half a tooth crown, or more, that is what we must tighten, or if you just do it, your chain is dead ..

to get a kit and change the channel , things vary quite a bike to another, but here are some answers to questions that commonly arise. Chain closed or open system? 1st scenario chain passes around the swing arm .. and you can get your channel, thus reinstall without having to open it, or anything having to dismount.

You can buy a closed chain, set at the factory. Second possibility, the chain passes in the reinforcement of the swingarm. Here the question does not arise, (the reinforcement is welded), you need to open the chain to remove it, and install an open chain-you close yourself.

Chain Tool grinder or for disassembly, reassembly bank chain for fear ... Third possibility, it passes behind the axis in the oscillating arm. Some will choose to dismantle the arms, so as not to have to open the old system, and especially to install a closed chain factory ...

That said, it is still not a lot of work, and some prefer open the old chain and crimp the news. The replacement of the chain kit can be an opportunity to refine motor skills by playing with the gear.

In racing, for example some will change up their gear to suit each circuit. Similarly, the purchase of a gear having a tooth gap in either direction will evolve motor as needed. A smaller gear or a larger ring.

To improve acceleration, but limiting the top speed. A larger sprocket or a smaller ring. To get longer and pushing the top speed, but with less acceleration. Open or crimp a motorcycle chain. Derive (dériveter) a motorcycle chain without worry. To derive no problem: either you have a chain tool, or you grind the ends of two axes on a maillion chain and a screwdriver you blow up the plate of the link. Then you take it as you would for a quick release. River (riveting) a motorcycle chain. To close the channel you have two options: either it comes with a quick release. (but often reserved for small and medium displacement).

Or, you have yourself crimp the last link. You parvindrez there with a chain-shore, which usually costs half the price that an installation in the workshop ... And will be useful for several facilities, or shorten your chain.

Avoid absolutely the hammer to drift and worse for riveting. First the result will not be guaranteed, and a channel that opens at full speed ... It's more than dangerous.

Then because you can distort the chain and cause unhealthy wear. Before you measure your actual kit chain wear. Choosing the right type of chain.

The basic rule is first to never take a lower quality than the original. Then you can go upmarket following your type of use. Depending on the type of conduct. Your conduct is more sporty and more powerful your machine is, the more the jerks on the chain will be significant.

So, the more you will have to climb in quality. A tourist route in road obviously does not demand the same reliability quune mx use, trial or gp (or quad, seeking many secondary transmission). Depending on the type of course.

Similarly, the hardness of the environment play. The mx uses, enduro, trials etc, are more aggressive than the road courses. In such cases, will therefore be preferred oring chains, O-rings that will be better protected from water, mud, sand, all these little things that love mechanics. After winding re-adjust the chain tension with the weight of the driver, or a little more, if you often take him an adult passenger. For assembly of the crown, place 2 drops of powerful grease on the bolt threads.

This is part of the bike strongly subject to vibrations and shocks. Think on some models, the change of gear can cause a change in the speed measurement. Always adjust the tension with the driver sitting on the bike. The chain tension changes with suspension travel.

It is therefore essential to make these motorcycle loaded settings, otherwise you end up with a much chain tension than expected. It is therefore necessary to perform two BE the operation. After just released the nut rear wheel axle, and against the nut of each tensioner progressively screw the side chain tensioner (to get to the proper voltage), then screw the other in the same way.

Tensioners pull the wheel axle to the rear, and thus tend chain. Use your markers on each tensioner to adjust identically. Check that the wheel is centered. You can check lalignement the wheel thanks to the graduations located on the swing arm, or by measuring the distance that it is between the ends of the swingarm pivot and the ends of the rear axle. Which must of course be equidistant from each side. Before tightening the nuts and bolts against, make sure the wheel axle is making good contact against the turnbuckles. Also make sure that the tensioning screw is locked in position, not cowards. Re-check the setting after final tightening. Sometimes the settings move during clamping. To avoid to have done all this for nothing, once everything is blocked, recheck the chain tension and alignment of the wheel.

Should prowling a chain kit? In general, we share the idea that any rolling piece should be rehearsed. On the chain-kit, perhaps this is less visible than in segments (breakage / clamping), tires (drop) or platelets (icing), but it nevertheless promotes good implementation of the three elements (channel, pinion, crown) and extends all the more their lifetime. Choose the delivery method before paying. Mondial relay only for mainland France not the islands, as the Corsican ..

processing time of your order can vary from 4 to 15 working days, please contact us before purchase !! locks, batteries, candles, kits chains, pinions, crowns, chains, disc dembrayage, air filters,, oil filters, filter gasoline, oils, engine seals, oil seals, brake levers and handles dembrayage, protected handles, jaws brake, fixed brake discs and floating, brake pads, motorbike tires, tires cross and enduro, tires scooter tires quad, inner tubes, lamps and headlamps, wheel bearings and steering bearings, spraychain, turn signals, mirrors, fork tubes, cables, tank caps, handlebars, bridges, screws, bits handlebars, valves and plugs of valves, contactors, crutches datelier, footstools, belts, exhausts, tool, top case and windshield. Helmets, rain wear, and anti-cold accessories, electric blanket tires, etc.

03.25.55.74.71. Monday to Friday from 9h-12h to 14h-18h. The item \The seller is \This item can be shipped to the following countries: European Union.

1. manufacturer part number: not applicable <\/ li>
2. brand - no brand / generic - <\/ li> <\/ Ul>