Yamaha Raptor Yamaha

Kit Chaine Comoplet MX Alpha Ors Quad Yamaha Yfm 660 R Raptor 01-05 2001-2005


Kit Chaine Comoplet MX Alpha Ors Quad Yamaha Yfm 660 R Raptor 01-05 2001-2005

Kit Chaine Comoplet MX Alpha Ors Quad Yamaha Yfm 660 R Raptor 01-05 2001-2005    Kit Chaine Comoplet MX Alpha Ors Quad Yamaha Yfm 660 R Raptor 01-05 2001-2005
Mx alpha ors oring with O-ring. Other qualities of available chains: standard, hyper strengthens oring, super reinforced contact us! Crown - open chain - sprocket - fastening/maillon. Sprocket: 13, crown 40, chain: not 520, number of links: 92. Other report available on misterbike! Contact us on 03.25.55.74.71 before purchase!

Choice of other gears: gable / crown here. Choice of other accessories and parts /. Chain brand : tsubaki /rk /kitchain japon /izumi/ sarkani according to stock. 10457cz13 / 103.52014046 + 102.52040020 / 20627cz42 + 140.5120001201.

This product is compatible with the following models. Yfm 660 r raptor 5lp, 2001 - 2005. A few colsails to replace your chain kit. Reinforced standard: (oro, eb) 250 cm3 max super reinforced: (rh) 500 cm3 max super reinforced: (rs, rs3, rx) 500 cm3 and more. Super oring: standard O-ring joints (orn) normal / intensive road.

Hyper oring: advanced O-ring joints (or) special sports use oring: O-ring joints competition (orh) use racing. Location of the chain kit. A few things to know...

How to see if it's time to change? The tension markers: with wear, the chain elongates and relaxes. To extend it, the wheel is pulled backwards thanks to the tensioners located against the nuts of the wheel axis. Close to these tendors, we find the tension markers. They are used to adjust the left and right tendors symmetrically and to see when approaching the limit stroke.

If by extending your chain, you get to the end of these landmarks, it's time to change it. And so in general, to change your chain kit.

The teeth of the pinion and crown: you can also observe the teeth of the pinion and crown. If they're rounded, even puffed, or totally twisted... It's definitely time to change. You can also test your chain by grabbing it between two fingers at the crown level, and pulling back. If you are able to discover half a tooth of the crown, or more, it is that either you have to stretch, or if you have just done so, that your chain is dead..

to fall a chain kit and change it, things vary pretty much from one bike to another, but here are some answers to the questions that you commonly ask. Closed chain or open chain? First case of figure the chain passes around the swinging arm... And you can pull out your chain, so reinstall one, without having to open it, or have nothing to disassemble.

So you can buy a closed chain, set in the factory. 2nd possibility, the chain passes in the reinforcement of the swinging arm: here the question does not arise, (the reinforcement is welded), you have to open the chain to exit it, and install an open chain that you will close yourself. Chain or grinder drive for disassembly, chain bank for reassembly... 3rd possibility, it passes behind the axis, in the swinging arm: some will choose to dismantle the arm, in order not to have to open the old chain, and especially in order to install a closed chain in the factory... That said, it still represents a lot of work, and some will prefer to open the old chain and set the new one.

The replacement of the chain kit can be an opportunity to refine the motoricity by playing on the gearbox. In racing, for example, some go so far as to modify their multiplication according to each circuit. Similarly, the purchase of a pinion with an additional or lesser tooth gap will allow the motor to evolve according to the needs: a smaller pinion, or a larger crown to increase accelerations, but by limiting the peak speed.

A larger pinion, or a smaller crown to pull longer and push the peak speed, but with less accelerations. Open or set a motorcycle chain.

Derivating (driving) a motorcycle chain without worries: to drift no problem: either you have a drift chain, or you grind the ends of the two axes on a grid of the chain, then with a screwdriver you blow the plate of the link. Then you remove this one as you would for a quick tie. River (riveter) a motorcycle chain: to close the chain you have two solutions: either it comes with a quick attachment. Which is rather simple and...

(but often reserved for small and medium-sized cylinders). Either, you have to set the last link yourself. You will get there with a chain bank, which usually costs half as much as a workshop installation... And you will be useful for several installations, or to shorten your chain. Absolutely avoid the hammer to drift and even worse to rivet: first the result will not be guaranteed, and a chain that opens at full speed... It is more than dangerous. Then because you can distort the chain and cause unhealthy wear and tear. Some tips for disassembly / reassembly.

Before you start, measure the actual wear and tear of your chain kit. Choosing the right type of chain: the basic rule, first of all, is never to take a lower quality than the original one. Then you can go up to range according to your type of use. Depending on the type of driving.

The more sporty your driving and the more powerful your machine, the more important the bumps on the chain. And so, the more quality you'll have to go up.

A road trip obviously does not require the same reliability as a use mx, trial or gp. (or quad, which greatly require secondary transmission). Depending on the type of route: similarly, the "hardness" of the environment will play.

The uses mx, enduro, trial etc., are more aggressive than the road circuits.

In this type of case, we will therefore prefer the oring chains, with o-ring joints that will be better protected from water, mud, sand. All those little things that mechanics love. After winding re-regulate the tension of the chain with the pilot's weight, or even a little more, if you often take an adult passenger. For the winding of the crown, put 2 drops of powerful grease on the threads of the bolts. It's a part of the bike that is heavily subjected to vibrations and shocks.

Think that on some models, the shift in gear can result in a change in speed measurement. Think about making the correction. Important: Always adjust the tension with the driver sitting on the motorcycle the tension of the chain changes with the suspension. It is therefore essential to make these motorcycle settings loaded, otherwise you will find yourself with a much more tense chain than expected.

It is therefore necessary to be two to perform the operation. Tighten the chain: after just unlocking the rear wheel axis nut, and the back nut of each tensioner, gradually screw the chain side tensioner (to get to the right tension), then screw the other in the same way. The tensioners pull the wheel axis backwards, thus stretching the chain.

Use the markers on each tensioner to adjust them in the same way. Check if the wheel is centered: you can check the alignment of the wheel with the graduations located on the oscillating arm, or by measuring the distance between the ends of the axis of the oscillating arm and the ends of the rear wheel axis. Which, of course, must be at equal distance from each side.

Tighten the wheel: before blocking the nuts and against nuts, check that the wheel axis is in contact with the tensioners. Similarly, make sure that the screws of the tensioners are blocked in position, not loose. Re-check the adjustment after final tightening.

Sometimes the settings move during tightening. To avoid having done all this for nothing, once everything is blocked, check again the tension of the chain and the alignment of the wheel. Should we walk around a chain kit?

In general, the idea is that every piece of rolling equipment should be around. On the chain kit, it may be less visible than on segments (cassage/lock), tires (fall) or pads (glacing), but it does favour a good installation of the three elements (chain, pinion, crown), and even longer their lifespan. Italian brand more than 250 times world champion, partners of the biggest international drivers. Regina equips many machines in the first climb.

Chains made in japon, reliability and robustness. Remarkable strength at affordable prices. Chains made in japon, for standart chains without O-rings. Other thousands of pieces with it.

The delays may vary from 2 to 15 working days, contact us before the purchase. New parts in their packaging. Anti-flying, batteries, candles, chain kits, sprockets, crowns, chains, clutch discs, air filters, oil filters, petrol filter, oils, motor seals, spi seals, brake levers and clutches, grip protections, brake jaws, fixed and floating brake discs, brake pads, motorcycle tires, cross and enduro tires, scooter tires, quad tires, air chambers, lamps and projectors, wheel bearings and steering bearings, spraychain, flashing machines, rear-viewers, forks tubes, cables, tank caps, guidance devices, bridges, screws, guide tips, valve valves and valve stoppers, contactors, workshop shells, footrests, belts, hatchings, tools, top case and windshields. Helmets, rainwear, anti-cold clothing and accessories, tire heating blanket, etc. 03.25.55.74.71 Monday to Friday from 9 a.

06.62.69.50.19 from 9 a. This item is in the category "auto, motorcycle - parts, accessories\moto: spare parts\other". The seller is "destocnet" and is located in this country: fr. This item can be shipped to the following country: whole world.
    Mark: - no mark/generic -

Kit Chaine Comoplet MX Alpha Ors Quad Yamaha Yfm 660 R Raptor 01-05 2001-2005    Kit Chaine Comoplet MX Alpha Ors Quad Yamaha Yfm 660 R Raptor 01-05 2001-2005